Big Show Shot Bags & Marker Bags for Productions

Big Show Shot Bag and Marker Bags

Big Show shot bags provide movable ballast for suitable production equipment. Coloured marker bags provide movable reference points for people, props and camera setups. They belong in the same equipment kit, but the job determines which bag to use and where it should go.

 Black Big Show shot bag and red, yellow and blue marker bags on a film equipment prep bench

Big Show shot bag and coloured marker bags in a film preparation setting. AI-generated editorial illustration based on product photographs.

Stanmart supplies Big Show shot bags in 5 kg, 10 kg and 15 kg sizes and 2.5 kg coloured marker bags.

We also offer shot bag hire for productions that need extra weight on specific dates.

Shot bags and marker bags at a glance

ProductListed optionsProduction use
Big Show shot bags5 kg, 10 kg and 15 kgBallast for compatible stands and suitable ground-supported equipment, in line with equipment requirements.
Coloured marker bags2.5 kg; red, black, blue, white and yellow listedTemporary references for blocking, prop resets and camera department checks.

A bag’s stated weight is its mass. It does not establish a stand’s load capacity, a wind rating or a lifting rating. Confirm the required quantities and current colour availability when ordering.

What is inside a Big Show shot bag?

Big Show shot bags contain small pieces of metal inside a flexible PVC outer. The loose fill allows the bag to conform to a suitable support instead of behaving like a rigid block. The black shot bags have a webbing carry handle. The supplier’s Big Show range information distinguishes shot bags, sand bags, marker bags and other shapes.

Crews sometimes use “sandbag” as a general equipment term. For ordering, specify the product, filled weight and quantity. A request for six bags leaves too much unresolved if the department actually needs six particular weights.

Using shot bags with lighting and grip equipment

A lighting setup can change substantially between shots. Raising a fixture, extending an arm or adding a flag changes the load and its position relative to the base. Ballast should therefore be checked as part of the complete setup, each time it changes.

Screen Safe Australia’s lighting guidance calls for lighting stands to be properly weighted or fixed to the ground. The stand manufacturer’s instructions and the responsible lighting or grip technician should determine the arrangement.

For C-stands, light stands and compatible background supports, establish:

  • The model, permitted load and intended configuration of the stand.
  • The complete attached load, including modifiers and accessories.
  • The working height, arm extension and direction of the load.
  • The approved ballast position and how the bag will remain in place.
  • The floor or ground condition and the route used by cast and crew.

Ballast needs to act through the intended part of the support. A bag placed beside a stand may contribute nothing to its stability. Keep weights clear of moving parts and access routes, and reassess the setup after repositioning.

Why matching the load kilogram for kilogram is unreliable

Overturning depends on leverage as well as mass. Moving a load farther from its support increases its turning effect. A 5 kg accessory on an extended arm therefore cannot be assessed simply by adding a 5 kg bag somewhere at the base.

Adding ballast also does not increase the rated capacity of a stand, grip head or boom. Stay within the manufacturer’s limits for the full assembly.

Exterior shoots need a separate assessment

Flags, reflectors and background fabrics can present a large area to the wind. Changes in exposure, ground slope and surface friction affect stability. The supplier’s weight-selection guidance identifies these factors rather than prescribing one weight for every situation.

Plan the exterior setup with the responsible technician, including monitoring conditions and when equipment must be lowered or taken down. Buying the heaviest available bag does not establish a safe wind limit.

Using marker bags for blocking and continuity

Marker bags are useful while a position is still being worked out. They can provide a visible reference during a blocking rehearsal, identify a prop’s reset location, or mark a position for the camera department to check. They are also useful where a temporary reference is needed without putting adhesive on the surface.

Make the reference precise. Agree whether the mark refers to the centre of the bag, an end or a measured offset from it. For example, if the bag sits beside a chair position, record the offset so another crew member can reset the chair consistently.

Agree the colour key within the production and record it with the relevant camera or continuity notes. A colour does not have a universal meaning. Check whether the marker is visible in the shot, in reflections or during a camera move.

Place raised markers clear of foot placement, tracking equipment and action routes. Move them before the take if the action could bring someone into contact with them. A weighted marker can stay put more readily than a loose paper note, but it still needs checking after a reset.

Marker bags or spike tape

A marker bag suits an adjustable reference outside the action path. Appropriately selected and tested spike tape is useful when the production needs a low-profile mark on an approved surface. Stanmart’s tapes and adhesives range includes marking options for different applications.

Choose with the location owner and floor finish in mind. A movable bag avoids an adhesive bond, but dirt underneath it can still scratch a finish. Tape requires a compatibility test and permission where relevant; a low-tack description alone does not establish that a surface is suitable.

Inspection and transport between locations

Check the outer, seams and handles before use. Check marker bag eyelets for damage or sharp edges. Remove leaking or damaged bags from service and deal with loose fill promptly. Carry bags rather than dragging them over a finished floor.

Plan the total load before packing. Ten 10 kg bags add 100 kg before cases or other equipment. Check vehicle and trolley capacities, secure the load for transport and plan unloading access. SafeWork NSW’s manual-task guidance explains why repetition, force and awkward posture matter as well as the weight of an individual item.

Buying or hiring shot bags in Sydney

Buying can suit a studio or production company that regularly uses the same kit. Hiring can suit a short shoot, an additional unit or a temporary increase in equipment. Compare the full cost, including transport, collection and the time the weights will be required.

Stanmart Film Services is based in Chatswood, Sydney. Send us your purchase or hire enquiry with the required weights, quantities, production dates and location. For hire, include the collection and return dates or delivery requirements so we can confirm availability and quote the arrangement.

Shop shot bags and marker bags, enquire about shot bag hire, or call 02 9417 3000.

Common production questions

How many shot bags does a C-stand need

There is no universal number. The answer depends on the stand, attached equipment, extension, ballast position and conditions. Have the responsible technician specify the arrangement within the equipment manufacturer’s limits.

Can I use a marker bag as ballast

Only where its mass, shape and placement meet the equipment requirements. A 2.5 kg marker bag should not be treated as a substitute for a specified heavier weight.

Can shot bags be suspended by their handles

Do not assume a carry handle or marker bag eyelet is a rated lifting point. Suspended loads require equipment and attachments specifically approved for that application.

Does Stanmart hire shot bags

Yes. Contact Stanmart with your dates, required weights and quantities. Hire availability and the collection or delivery arrangement are confirmed when quoting.

Recommended products

Leave a Reply

Your email address will not be published. Required fields are marked *


This site uses Akismet to reduce spam. Learn how your comment data is processed.